Aluminum Alloys: Fabrication, Characterization and Applications II / Edition 1

Aluminum Alloys: Fabrication, Characterization and Applications II / Edition 1

by Weimin Yin, Zhengdong Long
     
 

ISBN-10: 0873397355

ISBN-13: 9780873397353

Pub. Date: 02/01/2009

Publisher: Wiley

This book presents advancements in aluminum for the marketplace, covering all aspects of the physical and mechanical metallurgy of alloys. It addresses fundamental and applied research as well as product development, testing and implementation of aluminum foil, sheet, plate, extrusions, forgings and composites for end applications including automotive, aerospace

…  See more details below

Overview

This book presents advancements in aluminum for the marketplace, covering all aspects of the physical and mechanical metallurgy of alloys. It addresses fundamental and applied research as well as product development, testing and implementation of aluminum foil, sheet, plate, extrusions, forgings and composites for end applications including automotive, aerospace and marine transportation and packaging. Specific sections include development and applications; processing and properties; modeling; alloy characterization; corrosion and protection; and composites and foams.

Product Details

ISBN-13:
9780873397353
Publisher:
Wiley
Publication date:
02/01/2009
Pages:
228
Product dimensions:
6.08(w) x 9.11(h) x 0.49(d)

Table of Contents

Preface.

Editor & Organizer Information.

Alumiunum Alloys: Fabrication, Characterization and Applications II.

Development and Application.

Development of Low-Cost, High-Performance Al-Zn-Mg Alloy 7020 (J. Chinella).

Development of Twin-Belt Cast AA5XXX Series Aluminum Alloy Materials for Automotive Sheet Applications (P. Zhao, T. Anami, I. Okamoto, K. Mizushima, K. Gatenby, M. Gallerneault, S. Barker, K. Yasunaga, A. Goto, H. Kazama, and N. Hayashi).

Use of Aluminum in Electrical Applications (P. Pollak).

Re-use of Aluminum Turning Chips by Hot Extrusion (K. Pantke, and D. Biermann).

Processing and Properties.

Multiple Extrusion and Consolidation of Al-4Mg-1Zr (D. Garcia, R. Dashwood, M. Jackson, and D. Dye).

Al-Zn-Mg for Extrusion - Hot Workability (H. McQueen, P. Leo, and E. Cerri).

Microstructural Control through Heat Treatment Process in an Aerospace Aluminum Alloy (Z. Huda).

Influence of Ge-Si Additions on Aging Response and Property in 2xxx Alloys (L. Zhuang, S. Chen, A. Norman, A. Bürger, and S. Spangel).

Microstructure and Mechanical Properties of Cast Hypereutectic Al-Si Alloys with High Magnesium Content (A. Mandal, and M. Makhlouf).

Electron Microscopy of Commercial Purity Al-2024 (Al-Mg-Cu) after Accumulative Roll-Bonding (A. Kulovits, B. Webler, A. Deshpande, and J. Wiezorek).

Annealing Behavior of an Heavily Deformed Aluminum Alloy in 20 Tesla Magnetic Field (S. Adedokun).

Effects of Ultrasonic Treatment on Microstructures and Properties of Hypereutectic Al-Si Alloys (H. Feng).

Solidification and Processing of Aluminum Based Immiscible Alloys (H. Kotadia, J. Patel, Z. Fan, E. Doernberg, and R. Schmid-Fetzer).

Formability and Texture.

Bending Performance of Al-Mg-Si Alloy after Interrupted and Delayed Quench (C. Bezencon, J. Despois, J. Timm, A. Gupta, and C. Bassi).

The Effect of Microstructure on the Surface Finish of Extruded 6262 Aluminum Alloy Billet (Q. Han).

Deformation Textures and Plastic Anisotropy of AA6xxx at Warm Temperatures (M. Ghosh, A. Miroux, J. Sidor, and L. Kestens).

Formation of the {111}<110> and {111}<112> Shear Bands and the <111> Fiber Texture during Moderate and Heavy Wire Drawing of 5056 Al-Mg

Alloy (M. Shamsuzzoha, and F. Liu).

Pole Figure Characteristics of Annealed Aluminum Alloy 6061 in Different Magnetic Fields up to 30 Tesla (S. Adedokun).

Materials Characterization.

Influence of Heat Treatment on Low-Cycle Fatigue Behavior of an Extruded 6063 Aluminum Alloy (L. Chen, C. Ma, Y. Tian, X. Che, and P. Liaw).

Precipitation under Cyclic Strain in Solution-Treated Al-4wt%Cu I: Mechanical Behavior (A. Farrow, and C. Laird).

Precipitation under Cyclic Strain in Solution-Treated Al-4wt%Cu II: Precipitation Behavior (A. Farrow, and C. Laird).

Precipitation and Coarsening Kinetics and Effect of Mechanical Property of Al3Sc in Al-Sc Alloys (Q. Wen, F. Ye, M. Huang, J. Wang, and J. Lin).

Alloy Preparation Improvements at Alumar (F. Silva, J. Feitosa, A. Bizon, S. Silva, and C. Campos).

Modeling and Corrosion.

Analysis of Pulsed Forming Processes (S. Golovashchenko, and N. Bessonov).

Modelling Homogenization Heat Treatment of AA3003 Alloy (Q. Du, W. Poole, and M. Wells).

Welding Techniques and Corrosion Behavior of 5xxx Alloy for Marine Structural Application (Z. Long, S. Das, J. Kaufman, S. Ningileri, and Y. Wang).

Hydrogen Generation by Aluminum-Water Reactions (P. Rozenak, and E. Shani).

Splitting Water with Al Rich Alloys: Structure and Reaction Kinetics (G. Choi, J. Woodall, J. Ziebarth, C. Allen, J. Jeon, D. Sherman, and R. Kramer).

Composite and Foam.

Joining of Aluminum 5754 Alloy to Carbon Fiber Reinforced Polymers (CFRP) by Ultrasonic Welding (F. Balle, G. Wagner, and D. Eifler).

Effect of Particle Loading on the Properties of Al/SiC Metal Matrix Composites (B. Givens, W. Waggoner, K. Kremer, and M. Aghajanian).

Impact Properties and Microstructural Evolution of Weldable and Unweldable Aluminum-Scandium (Al-Sc) Alloys (W. Lee, and T. Chen).

Author Index.

Subject Index.

Read More

Customer Reviews

Average Review:

Write a Review

and post it to your social network

     

Most Helpful Customer Reviews

See all customer reviews >