CCNP Study Guide Kit

( 1 )


Here are the books you need to prepare for all four CCNP exams. These proven Sybex study guides provide:
  • Full coverage of all exam objectives—all the information you need to know
  • Practical information on key Cisco networking technologies...
See more details below
This Hardcover (2ND BK&CDR) is Not Available through
Sending request ...


Here are the books you need to prepare for all four CCNP exams. These proven Sybex study guides provide:
  • Full coverage of all exam objectives—all the information you need to know
  • Practical information on key Cisco networking technologies
  • Hundreds of challenging review questions, in the books and on the CDs
  • Leading-edge exam preparation software, including testing engines and electronic flashcards

Complete Coverage of Objectives for All Four Exams:

Remote Access (640-505)
  • Working with asynchronous connections
  • Using the Point-to-Point Protocol
  • Using Microsoft Windows 95/98
  • Setting up ISDN and dial-on-demand routing
  • Working with the Cisco 700 Series
  • Understanding X.25 and remote access issues
  • Working with Frame Relay
  • Using a backup link as a permanent connection
  • Understanding queuing and compression
  • Using NAT (Network Address Translation)
  • Setting up AAA

Switching (640-504)

  • Planning the campus network
  • Connecting the switch block
  • Designing and implementing VLAN technologies
  • Understanding Layer 2 Switching
  • Working with Spanning Tree Protocol (STP)
  • Using Spanning Tree with VLAN
  • Setting up Inter-VLAN Routing
  • Using Multi-Layer Switching (MLS)
  • Implementing Hot Standby Routing Protocol (HSRP)
  • Understanding multicast capabilities
  • Configuring multicast
  • Planning and setting up access policies

Routing (640-503)

  • Scaling large internetworks
  • The campus network
  • IP addressing
  • OSPF areas
  • Interconnecting OSPF areas
  • BGP basics
  • Configuring basic BGP
  • Monitoring, troubleshooting, and scalingBGP
  • Route optimization
  • Network scalability

Support (640-506)

  • Troubleshooting Cisco routers and switches
  • Choosing a resolution strategy
  • Using problem-solving models
  • Documenting potential causes and solutions
  • Common data link layer characteristics in campus LANs
  • Connection sequences in TCP/IP, Novell IPX, and AppleTalk
  • Minimizing troubleshooting tools' impact on router performance
  • Using Cisco IOS software commands and debug utilities
  • Resolving VLAN configuration problems
  • Resolving WAN, Frame Relay, and ISDN BRI problems
Read More Show Less

Product Details

  • ISBN-13: 9780782141559
  • Publisher: Sybex, Incorporated
  • Publication date: 11/8/2002
  • Edition description: 2ND BK&CDR
  • Edition number: 2
  • Pages: 2612
  • Product dimensions: 6.50 (w) x 9.50 (h) x 8.00 (d)

Meet the Author

Kevin Hales is a senior network engineer for the Utah Education Network, where he specializes in BGP and ATM and manages a statewide WAN.

Todd Lammle, CCNP, MCT, MCSE, CNI, and MCNE, is president of GlobalNet Training Solutions, Inc., and chief scientist of RouterSim, LLC. He is author of numerous Cisco and Microsoft study guides from Sybex.

Sean Odom, CCNP, MCSE, and CNX-Ethernet, teaches Cisco courses for GlobalNet Training Solutions. He has been a consultant to many large corporations and is author of white papers, labs, and Cisco related books.

Robert Padjen specializes in network design, data security, and business/technology modeling, as well as the development and presentation of network training programs. He is author and co-author of several Sybex study guides.

Kevin Wallace, CCNP, CCDP, CCSI, has served as Network Design Specialist for Walt Disney World and Network Manager for Eastern Kentucky University.

Read More Show Less

Read an Excerpt

From CCNP: Remote Access Study Guide

Chapter 4: Using Microsoft Windows 95/98

Any text on remote access would be remiss if it did not include a section on the world's most popular desktop operating system. It would be difficult to find a remote access solution that did not require support for Windows, particularly the consumer oriented platforms of Windows 95 and 98.

This chapter will focus on the configuration and support issues that surround this popular client software. Particular attention should be paid to the protocols that are supported and the configuration steps that are required on the client.

Reasons to Use Dial-Up Networking

Fortunately, not only is configuring and using dial-up networking in Windows 95/98 simple, but it also provides a broad base of services for remote users. These services include the following:
Automatic connection to Web sites Once configured, the operating system will automatically establish a dial-up connection in order to connect with a remote Web server. If a user simply types a URL into Internet Explorer, the modem will dial the Internet Service Provider (ISP) and request the Web page.

E-mail Mobile clients can connect with Microsoft Exchange or another e-mail service in the office. This provides an efficient way to communicate with colleagues.

File synchronization Remote users can obtain file updates and post their files on a server in the office for local users. Although Microsoft provides Configuring Dial-Up Networking with Windows 95/98 141 the Briefcase application for this purpose, Symantec's pcAnywhere and other such programs may be desired by more demanding users.

Remote control One alternative to high-bandwidth applications is remote control. Remote control software does exactly what it sounds like it does-keystrokes and mouse movements are sent to the host, and the host returns the image back to the remote user, allowing them to control the host. This solution allows only the screen images to be transferred, which can greatly reduce the required bandwidth for supporting the application.

Consider the following: a remote user on a dial-up connection needs to access a database that will result in 10 megabytes of data being transferred. With remote control, only the screen data will be sent for the session- with compression, this means that possibly less than 2 megabytes of data will be sent. Clearly, this bandwidth savings can be substantial. Note that remote control solutions must be connected to access data- unlike remote node solutions (where the modem acts as a slower network link), which use the remote user's local applications and data. Also, the bandwidth savings variance can differ significantly depending on the data demands of the application; in this context, remote control utilizes remote node solutions for transport, but the connection must be maintained for the duration of the remote control session.

Effectively, anything that a user can accomplish in the office is possible with dial-up networking. Unfortunately, the significantly lower bandwidth can make this impractical, depending on the application.

Configuring Dial-Up Networking with Windows 95/98

Dial-up networking in Windows 95/98 is extremely popular, perhaps for no other reason than that there are approximately 70 million clients that have it installed worldwide. From a client's perspective, the cost and effort needed to connect to the office remotely requires little more than a phone line and modem.

As you will see in this chapter, configuring and administrating a single Win-dows workstation for dial-up networking is very simple. Unfortunately, it is not as simple when you have to administer dial-up networking for thousands of remote users, and there are few existing tools that make this task easier.

Microsoft Windows 95 and 98 support remote dial-up networking with the protocols that provide transport for NetBIOS:

  • NetBEUI
  • IPX
  • IP
This is logical since Windows networking is still dependent upon the NetBIOS protocol and the name services that it provides. It is possible to add other protocols with third-party transport, but most designers find IP support to be sufficient, and they configure the client for PPP services.
See Chapter 3 for more information about the PPP protocol.

Configuring a Dial-Up Connection Client

The configuration of a Windows client for dial-up networking is a relatively painless process, although there are many different configuration options available, and good planning will greatly simplify an enterprise level deployment.

By default, the Windows 95/98 installation will include the basic files for installing and configuring a network connection. It is always a good idea, though, to have the original installation CD-ROM available since the setup program may need additional files to complete the installation. In addition, the latest service packs and updates should be installed-service packs contain many updates and problem fixes called patches. In general, the installation of patches is a benign event; however, before performing the upgrade, it is best to backup critical files and review the appropriateness of the patch. For multiple node upgrades, it is best to test the patch before you deploy it.

Check the Windows Web site at for the latest patches, service packs, and tips for configuring dial-up networking.

While there are many tools available for installing and configuring dial-up networking, this text will focus on the basic installation-PPP and TCP/IP protocols; however, multilink connections and scripting will all be presented.
The screen captures in this chapter, unless otherwise noted, are from Windows 98 Second Edition. While the screens will look similar, other versions of Windows may differ slightly.

Dial-Up Networking Application

To start configuring a dial-up connection, go to the Start menu and select Start -> Programs -> Accessories -> Communications -> Dial-Up Networking. This will open a dialog box similar to the one shown in Figure 4.1.

Figure 4.1 The Windows dial-up networking dialog box...

...On the system shown here, this is the first dial-up connection, so Windows provides only a Make New Connection icon. This brings up the Dial-Up Networking wizard. If there were other connections available, the user or administrator could select them to initiate a call or to go into an already established connection in order to reconfigure options.

Make New Connection Wizard

After selecting the Make New Connection icon, Windows will begin the Make New Connection wizard. The first dialog box of this wizard is shown in Figure 4.2.

Figure 4.2 Making a new connection...

...In this dialog box, you will select a name for the connection and set the type of modem that you will be using for the connection. If Windows did not detect and install a modem in the Select a Device box, you will need to correct this before continuing.

For instructions on installing a modem in Windows, please refer to the product documentation.

Note that in Figure 4.2, the Lucent Win Modem has been automatically selected, and the user has been prompted to provide a name for the connection....

Read More Show Less

Table of Contents

CCNP: Remote Access Study Guide
Assessment Test
Chapter 1: Cisco Solutions for Remote Access
Chapter 2: Asynchronous Connections
Chapter 3: Point-to-Point Protocol
Chapter 4: Using Microsoft Windows 95/98
Chapter 5: Integrated Services Digital Network (ISDN)
Chapter 6: Cisco 700 Series
Chapter 7: X.25 and LAPB
Chapter 8: Frame Relay
Chapter 9: Queuing and Compression
Chapter 10: Network Address Translation (NAT) and Port Address Translation (PAT)
Chapter 11: Centralized Security in Remote Access Networks
Appendix A: Practice Exam
Appendix B: Commands in This Study Guide
Appendix C: References

CCNP: Switching Study Guide

Assessment Test
Chapter 1: The Campus Network
Chapter 2: Connecting the Switch Block
Chapter 3: VLANs
Chapter 4: Layer 2 Switching and the Spanning Tree Protocol (STP)
Chapter 5: Using Spanning Tree with VLANs
Chapter 6: Inter-VLAN Routing
Chapter 7: Multi-Layer Switching (MLS)
Chapter 8: Hot Standby Routing Protocol (HSRP)
Chapter 9: Multicast
Chapter 10: Configuring Multicast
Chapter 11: Access Policies
Appendix A: Practice Exam
Appendix B: Commands Used in This Book
Appendix C: Internet Multicast Addresses

CCNP: Routing Study Guide

Assessment Test
Chapter 1: Scaling Large Internetworks
Chapter 2: Routing Principles
Chapter 3: IP Addressing
Chapter 4: OSPF Areas
Chapter 5: Interconnecting OSPF Areas
Chapter 6: IGRP and EIGRP
Chapter 7: BGP's Basic Components
Chapter 8: Configuring Basic BGP
Chapter 9: BGP Scalability and Advanced Features
Chapter 10: Route Optimization
Appendix A: Practice Exam
Appendix B: Commands in This Study Guide
Appendix C: Route Summarization

CCNP Support Study Guide

Assessment Test
Chapter 1: Troubleshooting Methodology
Chapter 2: Protocol Attributes
Chapter 3: Generic Troubleshooting Tools
Chapter 4: Cisco's Diagnostic Commands
Chapter 5: Applying Cisco's Diagnostic Tools
Chapter 6: Troubleshooting TCP/IP Connectivity
Chapter 7: Troubleshooting Serial Line and Frame Relay Connectivity
Chapter 8: Troubleshooting ISDN
Chapter 9: Troubleshooting Novell Connectivity
Chapter 10: Troubleshooting AppleTalk Connectivity
Chapter 11: Troubleshooting Switched Ethernet
Chapter 12: Cisco Support Functions
Appendix A: Practice Exam
Appendix B: Commands in This Study Guide
Read More Show Less

Customer Reviews

Average Rating 5
( 1 )
Rating Distribution

5 Star


4 Star


3 Star


2 Star


1 Star


Your Rating:

Your Name: Create a Pen Name or

Barnes & Review Rules

Our reader reviews allow you to share your comments on titles you liked, or didn't, with others. By submitting an online review, you are representing to Barnes & that all information contained in your review is original and accurate in all respects, and that the submission of such content by you and the posting of such content by Barnes & does not and will not violate the rights of any third party. Please follow the rules below to help ensure that your review can be posted.

Reviews by Our Customers Under the Age of 13

We highly value and respect everyone's opinion concerning the titles we offer. However, we cannot allow persons under the age of 13 to have accounts at or to post customer reviews. Please see our Terms of Use for more details.

What to exclude from your review:

Please do not write about reviews, commentary, or information posted on the product page. If you see any errors in the information on the product page, please send us an email.

Reviews should not contain any of the following:

  • - HTML tags, profanity, obscenities, vulgarities, or comments that defame anyone
  • - Time-sensitive information such as tour dates, signings, lectures, etc.
  • - Single-word reviews. Other people will read your review to discover why you liked or didn't like the title. Be descriptive.
  • - Comments focusing on the author or that may ruin the ending for others
  • - Phone numbers, addresses, URLs
  • - Pricing and availability information or alternative ordering information
  • - Advertisements or commercial solicitation


  • - By submitting a review, you grant to Barnes & and its sublicensees the royalty-free, perpetual, irrevocable right and license to use the review in accordance with the Barnes & Terms of Use.
  • - Barnes & reserves the right not to post any review -- particularly those that do not follow the terms and conditions of these Rules. Barnes & also reserves the right to remove any review at any time without notice.
  • - See Terms of Use for other conditions and disclaimers.
Search for Products You'd Like to Recommend

Recommend other products that relate to your review. Just search for them below and share!

Create a Pen Name

Your Pen Name is your unique identity on It will appear on the reviews you write and other website activities. Your Pen Name cannot be edited, changed or deleted once submitted.

Your Pen Name can be any combination of alphanumeric characters (plus - and _), and must be at least two characters long.

Continue Anonymously

    If you find inappropriate content, please report it to Barnes & Noble
    Why is this product inappropriate?
    Comments (optional)