Read an Excerpt
My Life and Work
By Henry Ford
OPEN ROAD INTEGRATED MEDIACopyright © 2015 Open Road Integrated Media, Inc.
All rights reserved.
THE BEGINNING OF BUSINESS
On May 31, 1921, the Ford Motor Company turned out Car No. 5,000,000. It is out in my museum along with the gasoline buggy that I began work on thirty years before and which first ran satisfactorily along in the spring of 1893. I was running it when the bobolinks came to Dearborn and they always come on April 2nd. There is all the difference in the world in the appearance of the two vehicles and almost as much difference in construction and materials, but in fundamentals the two are curiously alike — except that the old buggy has on it a few wrinkles that we have not yet quite adopted in our modern car. For that first car or buggy, even though it had but two cylinders, would make twenty miles an hour and run sixty miles on the three gallons of gas the little tank held and is as good to-day as the day it was built. The development in methods of manufacture and in materials has been greater than the development in basic design. The whole design has been refined; the present Ford car, which is the "Model T," has four cylinders and a self starter — it is in every way a more convenient and an easier riding car. It is simpler than the first car. But almost every point in it may be found also in the first car. The changes have been brought about through experience in the making and not through any change in the basic principle — which I take to be an important fact demonstrating that, given a good idea to start with, it is better to concentrate on perfecting it than to hunt around for a new idea. One idea at a time is about as much as any one can handle.
It was life on the farm that drove me into devising ways and means to better transportation. I was born on July 30, 1863, on a farm at Dearborn, Michigan, and my earliest recollection is that, considering the results, there was too much work on the place. That is the way I still feel about farming. There is a legend that my parents were very poor and that the early days were hard ones. Certainly they were not rich, but neither were they poor. As Michigan farmers went, we were prosperous. The house in which I was born is still standing, and it and the farm are part of my present holding.
There was too much hard hand labour on our own and all other farms of the time. Even when very young I suspected that much might somehow be done in a better way. That is what took me into mechanics — although my mother always said that I was born a mechanic. I had a kind of workshop with odds and ends of metal for tools before I had anything else. In those days we did not have the toys of to-day; what we had were home made. My toys were all tools — they still are! And every fragment of machinery was a treasure.
The biggest event of those early years was meeting with a road engine about eight miles out of Detroit one day when we were driving to town. I was then twelve years old. The second biggest event was getting a watch — which happened in the same year. I remember that engine as though I had seen it only yesterday, for it was the first vehicle other than horse-drawn that I had ever seen. It was intended primarily for driving threshing machines and sawmills and was simply a portable engine and boiler mounted on wheels with a water tank and coal cart trailing behind. I had seen plenty of these engines hauled around by horses, but this one had a chain that made a connection between the engine and the rear wheels of the wagon-like frame on which the boiler was mounted. The engine was placed over the boiler and one man standing on the platform behind the boiler shoveled coal, managed the throttle, and did the steering. It had been made by Nichols, Shepard & Company of Battle Creek. I found that out at once. The engine had stopped to let us pass with our horses and I was off the wagon and talking to the engineer before my father, who was driving, knew what I was up to. The engineer was very glad to explain the whole affair. He was proud of it. He showed me how the chain was disconnected from the propelling wheel and a belt put on to drive other machinery. He told me that the engine made two hundred revolutions a minute and that the chain pinion could be shifted to let the wagon stop while the engine was still running. This last is a feature which, although in different fashion, is incorporated into modern automobiles. It was not important with steam engines, which are easily stopped and started, but it became very important with the gasoline engine. It was that engine which took me into automotive transportation. I tried to make models of it, and some years later I did make one that ran very well, but from the time I saw that road engine as a boy of twelve right forward to to-day, my great interest has been in making a machine that would travel the roads. Driving to town I always had a pocket full of trinkets — nuts, washers, and odds and ends of machinery. Often I took a broken watch and tried to put it together. When I was thirteen I managed for the first time to put a watch together so that it would keep time. By the time I was fifteen I could do almost anything in watch repairing — although my tools were of the crudest. There is an immense amount to be learned simply by tinkering with things. It is not possible to learn from books how everything is made — and a real mechanic ought to know how nearly everything is made. Machines are to a mechanic what books are to a writer. He gets ideas from them, and if he has any brains he will apply those ideas.
From the beginning I never could work up much interest in the labour of farming. I wanted to have something to do with machinery. My father was not entirely in sympathy with my bent toward mechanics. He thought that I ought to be a farmer. When I left school at seventeen and became an apprentice in the machine shop of the Drydock Engine Works I was all but given up for lost. I passed my apprenticeship without trouble — that is, I was qualified to be a machinist long before my three-year term had expired — and having a liking for fine work and a leaning toward watches I worked nights at repairing in a jewelry shop. At one period of those early days I think that I must have had fully three hundred watches. I thought that I could build a serviceable watch for around thirty cents and nearly started in the business. But I did not because I figured out that watches were not universal necessities, and therefore people generally would not buy them. Just how I reached that surprising conclusion I am unable to state. I did not like the ordinary jewelry and watch making work excepting where the job was hard to do. Even then I wanted to make something in quantity. It was just about the time when the standard railroad time was being arranged. We had formerly been on sun time and for quite a while, just as in our present daylight-saving days, the railroad time differed from the local time. That bothered me a good deal and so I succeeded in making a watch that kept both times. It had two dials and it was quite a curiosity in the neighbourhood.
In 1879 — that is, about four years after I first saw that Nichols-Shepard machine — I managed to get a chance to run one and when my apprenticeship was over I worked with a local representative of the Westinghouse Company of Schenectady as an expert in the setting up and repair of their road engines. The engine they put out was much the same as the Nichols-Shepard engine excepting that the engine was up in front, the boiler in the rear, and the power was applied to the back wheels by a belt. They could make twelve miles an hour on the road even though the self-propelling feature was only an incident of the construction. They were sometimes used as tractors to pull heavy loads and, if the owner also happened to be in the threshing-machine business, he hitched his threshing machine and other paraphernalia to the engine in moving from farm to farm. What bothered me was the weight and the cost. They weighed a couple of tons and were far too expensive to be owned by other than a farmer with a great deal of land. They were mostly employed by people who went into threshing as a business or who had sawmills or some other line that required portable power.
Even before that time I had the idea of making some kind of a light steam car that would take the place of horses — more especially, however, as a tractor to attend to the excessively hard labour of ploughing. It occurred to me, as I remember somewhat vaguely, that precisely the same idea might be applied to a carriage or a wagon on the road. A horseless carriage was a common idea. People had been talking about carriages without horses for many years back — in fact, ever since the steam engine was invented — but the idea of the carriage at first did not seem so practical to me as the idea of an engine to do the harder farm work, and of all the work on the farm ploughing was the hardest. Our roads were poor and we had not the habit of getting around. One of the most remarkable features of the automobile on the farm is the way that it has broadened the farmer's life. We simply took for granted that unless the errand were urgent we would not go to town, and I think we rarely made more than a trip a week. In bad weather we did not go even that often.
Being a full-fledged machinist and with a very fair workshop on the farm it was not difficult for me to build a steam wagon or tractor. In the building of it came the idea that perhaps it might be made for road use. I felt perfectly certain that horses, considering all the bother of attending them and the expense of feeding, did not earn their keep. The obvious thing to do was to design and build a steam engine that would be light enough to run an ordinary wagon or to pull a plough. I thought it more important first to develop the tractor. To lift farm drudgery off flesh and blood and lay it on steel and motors has been my most constant ambition. It was circumstances that took me first into the actual manufacture of road cars. I found eventually that people were more interested in something that would travel on the road than in something that would do the work on the farms. In fact, I doubt that the light farm tractor could have been introduced on the farm had not the farmer had his eyes opened slowly but surely by the automobile. But that is getting ahead of the story. I thought the farmer would be more interested in the tractor.
I built a steam car that ran. It had a kerosene-heated boiler and it developed plenty of power and a neat control — which is so easy with a steam throttle. But the boiler was dangerous. To get the requisite power without too big and heavy a power plant required that the engine work under high pressure; sitting on a high-pressure steam boiler is not altogether pleasant. To make it even reasonably safe required an excess of weight that nullified the economy of the high pressure. For two years I kept experimenting with various sorts of boilers — the engine and control problems were simple enough — and then I definitely abandoned the whole idea of running a road vehicle by steam. I knew that in England they had what amounted to locomotives running on the roads hauling lines of trailers and also there was no difficulty in designing a big steam tractor for use on a large farm. But ours were not then English roads; they would have stalled or racked to pieces the strongest and heaviest road tractor. And anyway the manufacturing of a big tractor which only a few wealthy farmers could buy did not seem to me worth while.
But I did not give up the idea of a horseless carriage. The work with the Westinghouse representative only served to confirm the opinion I had formed that steam was not suitable for light vehicles. That is why I stayed only a year with that company. There was nothing more that the big steam tractors and engines could teach me and I did not want to waste time on something that would lead nowhere. A few years before — it was while I was an apprentice — I read in the World of Science, an English publication, of the "silent gas engine" which was then coming out in England. I think it was the Otto engine. It ran with illuminating gas, had a single large cylinder, and the power impulses being thus intermittent required an extremely heavy fly-wheel. As far as weight was concerned it gave nothing like the power per pound of metal that a steam engine gave, and the use of illuminating gas seemed to dismiss it as even a possibility for road use. It was interesting to me only as all machinery was interesting. I followed in the English and American magazines which we got in the shop the development of the engine and most particularly the hints of the possible replacement of the illuminating gas fuel by a gas formed by the vaporization of gasoline. The idea of gas engines was by no means new, but this was the first time that a really serious effort had been made to put them on the market. They were received with interest rather than enthusiasm and I do not recall any one who thought that the internal combustion engine could ever have more than a limited use. All the wise people demonstrated conclusively that the engine could not compete with steam. They never thought that it might carve out a career for itself. That is the way with wise people — they are so wise and practical that they always know to a dot just why something cannot be done; they always know the limitations. That is why I never employ an expert in full bloom. If ever I wanted to kill opposition by unfair means I would endow the opposition with experts. They would have so much good advice that I could be sure they would do little work.
The gas engine interested me and I followed its progress, but only from curiosity, until about 1885 or 1886 when, the steam engine being discarded as the motive power for the carriage that I intended some day to build, I had to look around for another sort of motive power. In 1885 I repaired an Otto engine at the Eagle Iron Works in Detroit. No one in town knew anything about them. There was a rumour that I did and, although I had never before been in contact with one, I undertook and carried through the job. That gave me a chance to study the new engine at first hand and in 1887 I built one on the Otto four-cycle model just to see if I understood the principles. "Four cycle" means that the piston traverses the cylinder four times to get one power impulse. The first stroke draws in the gas, the second compresses it, the third is the explosion or power stroke, while the fourth stroke exhausts the waste gas. The little model worked well enough; it had a one-inch bore and a three-inch stroke, operated with gasoline, and while it did not develop much power, it was slightly lighter in proportion than the engines being offered commercially. I gave it away later to a young man who wanted it for something or other and whose name I have forgotten; it was eventually destroyed. That was the beginning of the work with the internal combustion engine.
I was then on the farm to which I had returned, more because I wanted to experiment than because I wanted to farm, and, now being an all-around machinist, I had a first-class workshop to replace the toy shop of earlier days. My father offered me forty acres of timber land, provided I gave up being a machinist. I agreed in a provisional way, for cutting the timber gave me a chance to get married. I fitted out a sawmill and a portable engine and started to cut out and saw up the timber on the tract. Some of the first of that lumber went into a cottage on my new farm and in it we began our married life. It was not a big house — thirty-one feet square and only a story and a half high — but it was a comfortable place. I added to it my workshop, and when I was not cutting timber I was working on the gas engines — learning what they were and how they acted. I read everything I could find, but the greatest knowledge came from the work. A gas engine is a mysterious sort of thing — it will not always go the way it should. You can imagine how those first engines acted!
Excerpted from My Life and Work by Henry Ford. Copyright © 2015 Open Road Integrated Media, Inc.. Excerpted by permission of OPEN ROAD INTEGRATED MEDIA.
All rights reserved. No part of this excerpt may be reproduced or reprinted without permission in writing from the publisher.
Excerpts are provided by Dial-A-Book Inc. solely for the personal use of visitors to this web site.