Surface Treatment IV: Computer Methods and Experimental Measurements

Surface Treatment IV: Computer Methods and Experimental Measurements

by C. A. Brebbia
     
 

ISBN-10: 1853126977

ISBN-13: 9781853126970

Pub. Date: 10/28/1999

Publisher: WIT Press

This book contains a selection of papers presented at the Fourth International Conference on Computer Methods and Experimental Measurements for Surface Treatment Effects held in 1999. The aim of this series of meetings is to encourage international co-operation amongst scientists, technologists and engineers and to assist in a better understanding of areas such as…  See more details below

Overview

This book contains a selection of papers presented at the Fourth International Conference on Computer Methods and Experimental Measurements for Surface Treatment Effects held in 1999. The aim of this series of meetings is to encourage international co-operation amongst scientists, technologists and engineers and to assist in a better understanding of areas such as fatigue, fracture and wear resistance.

Product Details

ISBN-13:
9781853126970
Publisher:
WIT Press
Publication date:
10/28/1999
Series:
Computational and Experimental Methods Series
Pages:
416
Product dimensions:
6.30(w) x 9.06(h) x (d)

Table of Contents

Residual stress in magnetron sputtered TiN3
Tribological properties of duplex surface treated hot work tool steel sliding against aluminium alloy13
Standardization and some application of the evaluation method of defects in the ceramic coatings23
Formability of chromate conversion coating on zinc electroplated steel sheet33
Mechanical properties of diamond and DLC thin coating43
Applications of CVD diamond and DLC coatings55
Surface treatments of aluminium joints, adhesive thickness and radiation effects71
Effect of residual stress profile on hydrogen embrittlement susceptibility of prestressing steel83
Hybrid surface treatment of carbon steel by using a cavitating jet93
3D residual stresses around cold expanded holes in a new creep resistant aluminium alloy103
A critical evaluation of residual stresses in spheroidal graphite cast iron due to mechanical testing117
Modelling of residual stresses in surface layer treated by burnishing and nitriding127
The effect of injecting transverse electrical current on indentation fracture, friction and wear of WC-Co alloy139
Metal impregnation of aluminum oxide layers: influence of anodization conditions149
Formation and evaluation of calcium phosphates films by electrochemical method159
Anodisation of magnesium at high voltages169
An assessment of the effect of plasma nitriding and nitrocarburizing parameters on the corrosion resistance of sintered steel using the response surface method181
Corrosion behaviour of diamond-like carbon films prepared by ionization deposition197
Corrosion fatigue aspects in optimizing resistance against cracks growth of surface layers of steel components207
Use of the scribe and spotface techniques to assess the painted galvanised steel underfilm corrosion217
Method for testing fragments of sheet and rod-metal structures for stress corrosion225
Stress corrosion cracking of high-strength steel: influence of cyclic residual stresses243
Structural analyses of reaction layers between SiC and Ti-6Al-4V after laser embedding255
Reinforced SiC/Al composite layer produced by laser particle injection269
Improvement of fatigue lifetime of mechanically surface treated materials in the low cycle fatigue regime281
Influence of shot peening and high pressure water peening on near surface microstructure of 316 Ti stainless steel291
Residual stress distribution measurements in shot peened aluminium plates301
Thermal decay shot peening induced residual stresses during annealing of a bake-hardening steel311
Superfinishing and shot peening of surfaces to optimise roughness and stress321
Fatigue performance of a shot peened high-strength magnesium alloy331
Selective hardening and residual stress relaxation in shot peened Timetal 21S341
Fatigue response of various titanium alloys to shot peening349
Improvement of fatigue strength of the plate with a hole361
Fundamentals of grinding: surface conditions of ground WC-Co systems371
Numerical analysis of the temperature fields in the object during the burnishing rolling operation with the electrocontact heating381
A study on the lapping of ceramic balls389
Index of authors401

Read More

Customer Reviews

Average Review:

Write a Review

and post it to your social network

     

Most Helpful Customer Reviews

See all customer reviews >