Table of Contents
Orientation to the Electrical Trade (2.5 Hours) Trainee $20 ISBN 978-0-13-480474-3 Instructor $20 ISBN 978-0-13-480475-0 (Module ID 26101-17) Provides an overview of the electrical trade and discusses the career paths available to electricians.
Electrical Safety (10 Hours) Trainee $20 ISBN 978-0-13-480477-4 Instructor $20 ISBN 978-0-13-480478-1 (Module ID 26102-17) Covers safety rules and regulations for electricians, including precautions for electrical hazards found on the job. Also covers the OSHA-mandated lockout/tagout procedure.
Introduction to Electrical Circuits (7.5 Hours) Trainee $20 ISBN 978-0-13-480479-8 Instructor $20 ISBN 978-0-13-480480-4 (Module ID 26103-17) Introduces electrical concepts used in Ohm’s law applied to DC series circuits. Covers atomic theory, electromotive force, resistance, and electric power equations.
Electrical Theory (7.5 Hours) Trainee $20 ISBN 978-0-13-480481-1 Instructor $20 ISBN 978-0-13-480482-8 (Module ID 26104-17) Introduces series, parallel, and series parallel circuits. Covers resistive circuits, Kirchhoff’s voltage and current laws, and circuit analysis.
Introduction to the National Electrical Code® (7.5 Hours) Trainee $20 ISBN 978-0-13-480483-5 Instructor $20 ISBN 978-0-13-480485-9 (Module ID 26105-17) Provides a road map for using the NEC®. Introduces the layout and the types of information found within the code book. Allows trainees to practice finding information using an easy-to-follow procedure.
Device Boxes (10 Hours) Trainee $20 ISBN 978-0-13-480487-3 Instructor $20 ISBN 978-0-13-480486-6 (Module ID 26106-17) Covers the hardware and systems used by an electrician to mount and support boxes, receptacles, and other electrical components. Also covers NEC® fill and pull requirements for device, pull, and junction boxes under 100 cubic inches.
Hand Bending (10 Hours) Trainee $20 ISBN 978-0-13-480488-0 Instructor $20 ISBN 978-0-13-480489-7 (Module ID 26107-17) Introduces conduit bending and installation. Covers the techniques for using hand-operated and step conduit benders, as well as cutting, reaming, and threading conduit.
Raceways and Fittings (20 Hours) Trainee $20 ISBN 978-0-13-480491-0 Instructor $20 ISBN 978-0-13-480490-3 (Module ID 26108-17) Introduces the types and applications of raceways, wireways, and ducts. Stresses the applicable NEC® requirements.
Conductors and Cables (10 Hours) Trainee $20 ISBN 978-0-13-480494-1 Instructor $20 ISBN 978-0-13-480492-7 (Module ID 26109-17) Focuses on the types and applications of conductors and covers proper wiring techniques. Stresses the applicable NEC® requirements.
Basic Electrical Construction Drawings (7.5 Hours) Trainee $20 ISBN 978-0-13-480496-5 Instructor $20 ISBN 978-0-13-480495-8 (Module ID 26110-17) Describes electrical prints, drawings, and symbols, and the types of information that can be found on schematics, one-lines, and wiring diagrams.
Residential Electrical Services (15 Hours) Trainee $20 ISBN 978-0-13-478332-1 Instructor $20 ISBN 978-0-13-478341-3 (Module ID 26111-17) Covers the electrical devices and wiring techniques common to residential construction and maintenance. Allows trainees to practice making service calculations. Stresses the applicable NEC® requirements.
Electrical Test Equipment (5 Hours) Trainee $20 ISBN 978-0-13-478339-0 Instructor $20 ISBN 978-0-13-478340-6 (Module ID 26112-17) Covers proper selection, inspection, and use of common electrical test equipment, including voltage testers, clamp-on ammeters, ohmmeters, multimeters, phase/motor rotation testers, and data recording equipment. Also covers safety precautions and meter category ratings.
